-
Journal of Orthopaedic Research :... May 2016Acrylic bone cement has a variety of applications in orthopedic surgery. Primary uses in total arthroplasties are limited to prostheses fixation and antibiotic delivery.... (Review)
Review
Acrylic bone cement has a variety of applications in orthopedic surgery. Primary uses in total arthroplasties are limited to prostheses fixation and antibiotic delivery. With the large number of total joint arthroplasties expected to continue to rise, understanding the role bone cement plays in the success of total joint arthroplasty can have a significant impact on daily practice. The literature is inconclusive on whether cemented or cementless fixation technique is superior, and choice of fixation type is mainly determined by surgeon preference and experience. Surgeons should understand that if poor techniques exist, short-term outcomes of the replaced joint may be at risk. Statement of clinical significance: This article attempts to clarify some points of bone cement use through a review of the mechanical properties related to bone cement, a comparison to alternative materials, influence of additives, and the effects on surgical outcomes. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 34:737-744, 2016.
Topics: Arthroplasty, Replacement; Bone Cements; Humans; Polymethyl Methacrylate
PubMed: 26852143
DOI: 10.1002/jor.23184 -
Orthopaedic Surgery Nov 2017One of its most serious complications associated with arthroplasty is the development of infections. Although its prevalence is only between 0.5% and 3%, in some cases... (Review)
Review
One of its most serious complications associated with arthroplasty is the development of infections. Although its prevalence is only between 0.5% and 3%, in some cases it can lead to death. Therefore, an important challenge in joint surgery is the prevention of infections when an arthroplasty is performed. The use of antibiotic-loaded cements could be a suitable tool due to numerous advantages. The main advantage of the use of antibiotic loading into bone cement derives directly from antibiotic release in the effect site, allowing achievement of high concentrations at the site of action, and minimal or no systemic toxicity. This route of administration was first described by Buchholz and Engelbrecht. In the case of infection treatment, this is an established method and its good results have been confirmed. However, its role in infection prevention, and, therefore, the use of these systems in clinical practice, has proved controversial because of the uncertainty about the development of possible antibiotic resistance after prolonged exposure time, their effectiveness, the cost of the systems, toxicity and loosening of mechanical properties. This review discusses all these topics, focusing on effectiveness and safety, antibiotic decisions, cement type, mixing method, release kinetics and future perspectives. The final objective is to provide the orthopaedic surgeons the right information in their clinical practice based on current evidence.
Topics: Anti-Bacterial Agents; Arthroplasty, Replacement; Bone Cements; Humans; Joint Prosthesis; Prosthesis-Related Infections; Treatment Outcome
PubMed: 29178309
DOI: 10.1111/os.12351 -
PloS One 2022The purpose of this study was to investigate the effect of incorporating chitosan (Ch) and chitosan oligosaccharides (ChO) into the commercially premixed...
BACKGROUND AND PURPOSE
The purpose of this study was to investigate the effect of incorporating chitosan (Ch) and chitosan oligosaccharides (ChO) into the commercially premixed antibiotic-loaded bone cement (ALBC). We compare antibiotic release profiles, antibacterial activity, and mechanical properties among different ALBC formulations. The hypothesis was that increasing the amount of Ch and ChO in the cement mixture would increase the antibiotics released and bacterial control. ALBC mixed with Ch or ChO may create a greater effect due to its superior dissolving property.
MATERIALS AND METHODS
The bone cement samples used in this project were made from Copal® G+V composed of vancomycin and gentamicin. To prepare the Ch and the ChO mixed bone cement samples, different amounts of Ch and ChO were added to the polymethylmethacrylate matrix with three concentrations (1%, 5%, and 10%). Drug elution assay, antimicrobial assay, in vitro cytotoxicity, and mechanical properties were conducted.
RESULTS
Bone cement samples made from Copal® G+V alone or combined with Ch or ChO can release vancomycin and gentamicin into the phosphate-buffered saline. Mixing ChO into the bone cements can increase the amount of drug released more than Ch. ChO 10% gave the highest amount of antibiotics released. All samples showed good antibacterial properties with good biocompatibility in vitro. The microhardness values of the Ch and ChO groups increased significantly compared to the control group. In all groups tested, the microhardness of bone cements was reduced after the drug eluted out. However, this reduction of the Ch and ChO groups was in line with the control.
INTERPRETATION
Various attempts have been made to improve the ALBC efficacy. In our study, the best bone cement formulation was bone cement mixed with ChO (10%), which had the highest drug release profiles, was biocompatible, and contained antibacterial properties with acceptable mechanical properties. This phenomenon could result from the superior water solubility of the ChO. When ChO leaves the bone cement specimens, it generates pores that could act as a path that exposes the bone cement matrix to the surrounding medium, increasing antibiotic elution. From all above, ChO is a promising substance that could be added to ALBC in order to increase the drug elution rate. However, more in vitro and in vivo experiments are needed before being used in the clinic.
Topics: Bone Cements; Chitosan; Anti-Bacterial Agents; Vancomycin; Sulindac; Gentamicins; Glass Ionomer Cements; Dental Materials; Oligosaccharides
PubMed: 36449553
DOI: 10.1371/journal.pone.0276604 -
ACS Biomaterials Science & Engineering Mar 2023Current bone cement systems often demand free radical or metal-related initiators and/or catalysts for the crosslinking process, which may cause serious toxicity to the...
Current bone cement systems often demand free radical or metal-related initiators and/or catalysts for the crosslinking process, which may cause serious toxicity to the human body. In addition, the resultant dense scaffolds may have a prolonged degradation time and are difficult for cells to infiltrate and form new tissue. In this study, we developed a porous "click" organic-inorganic nanohybrid (PO-click-ON) cement that crosslinks via metal-free biorthogonal click chemistry and forms porous structures mimicking the native bone tissue via particulate leaching. Strain-promoted click reaction enables fast and efficient crosslinking of polymer chains with the exclusion of any toxic initiator or catalyst. The resulting PO-click-ON implants supported exceptional stem cell adhesion and osteogenic differentiation with a large portion of stem cells infiltrated deep into the scaffolds. study using a rat cranial defect model demonstrated that the PO-click-ON system achieved outstanding cell adsorption, neovascularization, and bone formation. The porous click cement developed in this study serves as a promising platform with multifunctionality for bone and other tissue engineering applications.
Topics: Humans; Rats; Animals; Bone Cements; Osteogenesis; Tissue Engineering; Bone and Bones; Stem Cells
PubMed: 36854041
DOI: 10.1021/acsbiomaterials.2c01482 -
Journal of Orthopaedic Research :... Nov 2018The use of larger prosthetic femoral heads in total hip arthroplasty (THA) has increased considerably in recent years in response to the need to improve joint stability... (Comparative Study)
Comparative Study
The use of larger prosthetic femoral heads in total hip arthroplasty (THA) has increased considerably in recent years in response to the need to improve joint stability and reduce risk of dislocation. However, data suggests larger femoral heads are associated with higher joint failure rates. For cemented implants, ensuring the continued integrity of the cement mantle is key to long term fixation. This paper describes an investigation into the effect of variation in femoral head size on stresses in the acetabular cement mantle and pelvic bone. Three commonly used femoral head sizes: 28, 32, and 36 mm diameter were investigated. The study was undertaken using a finite element model validated using surface strains obtained from Digital Image Correlation (DIC) during experimentation on a composite hemipelvis implanted with a cemented all-polyethylene acetabular cup. Following validation, the models were used to investigate stresses in the pelvic bone and acetabular cement mantle resulting from two loading scenarios; an average weight subject (700 N) and an overweight subject (1,000 N) undertaking a single leg stand. We found that the highest peak stresses occurred in the anterosuperior and posterosuperior regions of the bone-cement interface, in the line of action of the load, where debonding usually initiates. Stress on the cortical bone-cement interface increased with femoral head diameter by up to 9% whilst stresses in the trabecular bone remained relatively invariant. Our findings may help to explain higher joint failure rates associated with larger femoral heads. © 2018 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:2966-2977, 2018.
Topics: Arthroplasty, Replacement, Hip; Bone Cements; Finite Element Analysis; Hip Prosthesis; Humans; Models, Biological; Pelvic Bones; Stress, Mechanical
PubMed: 29774956
DOI: 10.1002/jor.24052 -
Hip International : the Journal of... 2015Creating bi-laminar cement mantles as part of revision hip arthroplasty is well-documented but there is a lack of data concerning the effect of cement brand on the...
Creating bi-laminar cement mantles as part of revision hip arthroplasty is well-documented but there is a lack of data concerning the effect of cement brand on the procedure. The aim of this study was to compare the shear strength of bi-laminar cement mantles using various combinations of two leading bone cement brands.Bi-laminar cement mantles were created using Simplex P with Tobramycin, and Palacos R+G: Simplex-Simplex (SS); Simplex-Palacos (SP); Palacos-Simplex (PS); and Palacos-Palacos (PP). Additionally, specimens were produced by rasping (R) the surface of the original mantle, or leaving it unrasped (U), leading to a total of eight groups (n = 10). Specimens were loaded in shear, at 0.1 mm/min, until failure, and the maximum shear strength calculated.The highest mean shear strength was found in the PSU and PSR groups (23.69 and 23.89 MPa respectively), and the lowest in the PPU group (14.70 MPa), which was significantly lower than all but two groups. Unrasped groups generally demonstrated greater standard error than rasped groups.In a further comparison to assess the effect of the new cement mantle brand, irrespective of the brand of the original mantle, Simplex significantly increased the shear strength compared to Palacos with equivalent preparation.It is recommended that the original mantle is rasped prior to injection of new cement, and that Simplex P with Tobramycin be used in preference to Palacos R+G irrespective of the existing cement type. Further research is needed to investigate more cement brands, and understand the underlying mechanisms relating to cement-in-cement procedures.
Topics: Arthroplasty, Replacement, Hip; Bone Cements; Humans; Materials Testing; Polymethyl Methacrylate; Prosthesis Design; Prosthesis Failure; Reoperation; Shear Strength
PubMed: 25044271
DOI: 10.5301/hipint.5000178 -
Scientific Reports Jul 2021This study aimed to evaluate the efficacy and safety of bone cement-augmented pedicle screw fixation for stage III Kümmell disease. Twenty-five patients with stage III...
This study aimed to evaluate the efficacy and safety of bone cement-augmented pedicle screw fixation for stage III Kümmell disease. Twenty-five patients with stage III Kümmell disease who received bone cement-augmented pedicle screw fixation at the First Affiliated Hospital of Guangzhou University of Chinese Medicine between June 2009 and December 2015 were enrolled. All patients were females with a history of osteoporosis. The vertebral Cobb angle (V-Cobb angle), the fixed segment Cobb Angle (S-Cobb angle), pelvic parameters, visual Analogue Scale (VAS) score, and Oswestry Disability Index (ODI) were assessed preoperatively, postoperatively and at the final follow-up. Complications, loosening rate, operation time, and intraoperative bleeding were recorded. The average lumbar vertebral density T-value was - 3.68 ± 0.71 SD, and the average age was 71.84 ± 5.39. The V-Cobb angle, S-Cobb angle, and Sagittal Vertical Axis (SVA) were significantly smaller postoperatively compared to the preoperative values. The VAS and ODI at 1 month after surgery were 3.60 ± 1.00 and 36.04 ± 6.12%, respectively, which were both significantly lower than before surgery (VAS: 8.56 ± 1.04, ODI: 77.80 ± 6.57%). Bone cement-augmented pedicle screw fixation is a safe and effective treatment for stage III Kümmell disease. It can effectively correct kyphosis, restore and maintain sagittal balance, and maintain spinal stability.
Topics: Aged; Bone Cements; Female; Fracture Fixation, Internal; Humans; Male; Osteonecrosis; Pedicle Screws; Spinal Diseases; Treatment Outcome
PubMed: 34211025
DOI: 10.1038/s41598-021-93013-1 -
PloS One 2021This study compares the strength of the native bone-cement bond and the old-new cement bond under cyclic loading, using third generation cementing technique, rasping and...
This study compares the strength of the native bone-cement bond and the old-new cement bond under cyclic loading, using third generation cementing technique, rasping and contamination of the surface of the old cement with biological tissue. The possible advantages of additional drilling of the cement surface is also taken into account. Femoral heads from 21 patients who underwent a total hip arthroplasty performed for hip arthritis were used to prepare bone-cement samples. The following groups of samples were prepared. A bone-cement sample and a composite sample of a 6 weeks old cement part attached to new cement were tested 24 hours after preparation to avoid bone decay. Additionally, a uniform cement sample was prepared as control (6 weeks polymerization time) and 2 groups of cement-cement samples with and without anchoring drill hole on its surface, where the old cement polymerized for 6 weeks before preparing composite samples and then another 6 weeks after preparation. The uniaxial cyclic tension-compression tests were carried out using the Zwick-Roell Z020 testing machine. The uniform cement sample had the highest ultimate force of all specimens (n = 15; Rm = 3149 N). The composite cement sample (n = 15; Rm = 902 N) had higher ultimate force as the bone-cement sample (n = 31; Rm = 284 N; p <0.001). There were no significant differences between composite samples with 24 hours (n = 15; Rm = 902 N) and 6 weeks polymerization periods (n = 22; Rm = 890 N; p = 0.93). The composite cement samples with drill hole (n = 16; Rm = 607 N) were weaker than those without it (n = 22; Rm = 890 N; p < 0.001). This study shows that the bond between the old and new cement was stronger than the bond between cement and bone. This suggests that it is better to leave the cement that is not loosened from the bone and perform cement in cement revision, than compromising bone stock by removal of the old cement with the resulting weaker cement-bone interface. The results support performing cement-in-cement revision arthroplasty The drill holes in the old cement mantle decrease cement binding strength and are not recommended in this type of surgery.
Topics: Arthroplasty, Replacement, Hip; Biomechanical Phenomena; Bone Cements; Hip Prosthesis; Humans; Materials Testing; Reoperation
PubMed: 33571251
DOI: 10.1371/journal.pone.0246740 -
Tissue Engineering. Part C, Methods Dec 2019The ultimate challenge of tissue engineering research is the translation of experimental knowledge into clinical application. In the preclinical testing phase of any new...
The ultimate challenge of tissue engineering research is the translation of experimental knowledge into clinical application. In the preclinical testing phase of any new therapy, animal models remain the gold standard. Therefore, the methodological choice of a suitable model is critical to meet the requirements for a safe clinical application of the developed treatment. For instance, we have shown in rats that the application of calcium phosphate cement (CPC)/propylene glycol alginate (PGA) with bone morphogenetic protein (BMP)-2 or fibroblast growth factor (FGF)-2 resulted in the regeneration of periodontal defects. However, it is debated whether using small models form a predictive method for translation to larger species. At the same time, the 3R framework is encouraged as guiding principles of the ethical use of animal testing. Therefore, based on the successful rat study, the objective of this study was to further investigate the periodontal regenerative efficacy of the CPC/BMP and PGA/FGF system in a periodontal defect model with a low number of nonhuman primates (NHPs). Three -overstocked from breeding for other purposes-were used (reuse of animals and appropriateness of the experimental animal species according to 3R framework). Three-wall periodontal defects were surgically created in the mandible. In total, 10 defects were created and distributed over two groups: (1) control group: PGA+CPC ( = 5) and (2) experimental group: PGA/FGF+CPC/BMP ( = 5). After 3 months, tissue regeneration was evaluated by histomorphometry and radiographic measurements. Data showed that epithelial downgrowth, cementum, and ligament regeneration were significantly enhanced in the experimental group compared with the control group ( = 5; = 0.013, = 0.028, and = 0.018, respectively). However, the amount of newly formed bone did not differ ( = 0.146). Overall, as a translational proof-of-principle study, the hybrid periodontal regenerative method of CPC/BMP+PGA/FGF promoted periodontal regeneration in NHPs. This study warrants the application of CPC/BMP/PGA/FGF in clinical trials. Impact Statement This study validated an earlier successful periodontal regeneration strategy from a rat model into a few spare nonhuman primates (NHPs). The hybrid periodontal regenerative method of calcium phosphate cement (CPC)/bone morphogenetic protein (BMP)-2/propylene glycol alginate (PGA)/fibroblast growth factor (FGF)-2 promoted periodontal regeneration in NHPs, which corroborated the previous rat results. This translational approach was a very practical option and thus reduced the number and species of experimental animals in translational research. These results found in NHPs indicate a consistent conclusion with the earlier findings in the rat model. It further warrants the application of CPC/BMP-2+PGA/FGF-2 in human clinical trials.
Topics: Animals; Bone Cements; Bone Morphogenetic Protein 2; Bone Regeneration; Fibroblast Growth Factor 2; Gels; Humans; Macaca fascicularis; Periodontium
PubMed: 31701811
DOI: 10.1089/ten.TEC.2019.0160 -
American Journal of Veterinary Research Dec 2023To determine setting and temperature properties of diluted polymethyl methacrylate (PMMA) bone cement in vitro to assess utility for vocal fold augmentation in horses.
OBJECTIVE
To determine setting and temperature properties of diluted polymethyl methacrylate (PMMA) bone cement in vitro to assess utility for vocal fold augmentation in horses.
SAMPLES
4 dilutions of PMMA equivalent to volumes of 15 mL, 20 mL, 25 mL, and 30 mL PMMA powder (PMMAp) in 10 mL solvent.
METHODS
For each volume PMMAp, setting times (tset), peak temperatures (Tmax), and times to peak temperature (tmax) were determined using a temperature data logger in a 4-mL volume of PMMA. Injectability was assessed in vitro by documenting the force required to inject 0.2 mL PMMA through an 18-gauge 3.5-inch spinal needle attached to a 6-mL syringe at 1-minute intervals. Working time (twork) was calculated from a linear regression of injectability.
RESULTS
Peak temperatures increased with increasing volume of PMMAp: 56 °C, 86 °C, 99 °C, and 101 °C. Times for tset, twork, and tmax were inversely proportional to PMMA concentrations, resulting in tset of 23, 21, 17, and 14 minutes; twork of 22.75, 12.25, 7, and 4 minutes; and tmax of 28, 24, 19, and 16 minutes, respectively, for 15, 20, 25, and 30 mL PMMAp. Pairwise comparisons for all analyses were significant apart from Tmax for 25 and 30 mL PMMAp (P = .96) and twork for 20 and 25 mL PMMAp (P = .06).
CLINICAL RELEVANCE
Decreasing the concentration of PMMA bone cement resulted in longer working times and setting times; however, peak temperatures did not differ between the 2 strongest concentrations. Further research is warranted to quantify diluted PMMA properties for in vivo use for vocal fold augmentation in horses.
Topics: Animals; Horses; Polymethyl Methacrylate; Bone Cements; Temperature; Injections
PubMed: 37739393
DOI: 10.2460/ajvr.23.05.0110